Keyence LS-5000 Manual do Utilizador Página 35
- Página / 132
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 6 Normal Mode
29
6
6.4 Setting Functions
Names and functions
Tag/Button Function Description Reference
page
DISPLAY HOLD Hold A measured value can be held or reset. 30
DATA ZERO Auto-zero A measured value can be instantaneously reset to “0.000”. 31
SCREEN Screen Selection The DISPLAY DATA screen or DISPLAY GRAPH screen 32 to 34
can be selected.
LIMIT SETUP Limit Setup 7 level tolerance limits can be set for each output. 35
CALIB Calibration Setup Minute measurement fluctuations caused by a change in the 36
target surface condition or target inclination can be corrected.
PROGRAM Program Selection Measurement data is stored and called as programs. 38
AREA Area Setup DIA, T.EDGE, B.EDGE or SEG(m,n) can be selected. 39
OUTPUT Calculation Setup Calculation can be performed with each measuring area 41
(A1 to A4).
Average Measurement results can be averaged. 44
M. Mode Nine measuring modes are provided. 46 to 53
Offset Any value can be added to or subtracted from the displayed 55
value.
Digit Sets the number of digits after the decimal point. 54
Analog Output An analog voltage (within ±10 V) proportional to the displayed 57
value can be output.
I/O Slot Setup Expansion I/O boards can be set. 59
INSPECT Inspect The scanning head conditions (optical axis, intensity) can 60
be checked.
UTILITY One-Scan Function Data obtained with only one surface of the 12-surface polygon 62
mirror becomes effective.
Program Selection The program selection method (front panel or rear terminals) 64
can be selected.
Display Unit The display units can be selected (“mm” or “inch”). 65
Area Check The number of edges in the measuring area can be 66
checked.
Initialize All settings are reset to the initial values. 67
Mode Change Normal mode or Pitch mode can be selected. 68
OPTIONS
LASER ON DISPLAY DATA
NOR
MAL
P. 1
OFF OFF
ZERO HOLD
SCREEN
DISPLAY
DATA
LIMIT
SETUP
PROGRAMCALIB
OPTIONS
Button
Tag
- LS-5000 Series 1
- Safety Precautions 2
- Warranty 3
- Contents 4
- Chapter 6 Normal mode 5
- Chapter 7 Pitch Mode 5
- Chapter 8 RS-232C I/O 6
- Chapter 9 Expansion I/O Board 6
- WARRANTIES AND DISLAIMERS 125 6
- Chapter 1 7
- 1.1 Classification 8
- 1.2 Warning Labels 8
- 1.3 Label Location 9
- 1.4 Safety Consideration 9
- Laser emission remote 10
- LS-5121T 11
- 1.6 Preparation for Operation 12
- Chapter 2 13
- 2.1.1 System Configuration 14
- Frame cover Frame cover 15
- Transmitter Receiver 16
- LS-C3 (3 m) 16
- To ROM board 16
- Frame cover Frame cover 17
- 5 • 0 0 0 0 – 18
- 2.3 Part Names 19
- LS-5041/5121 (Scanning head) 20
- Chapter 3 21
- 3.1 Quick Start Reference 22
- Chapter 4 23
- Chapter 4 Installation 24
- DIN rail 25
- Chapter 5 27
- 5.1 Area/Segment/Edge 28
- 5.2 Normal Mode 28
- 5.2.1 DIA Mode 29
- 5.2.3 SEG (m,n) Mode 29
- 5.3 Pitch Mode 30
- Chapter 6 31
- 6.1 Normal Mode Screens 32
- 6.2 Initial Screen 33
- DIAHEAD2 34
- ( 2, 3) 34
- 6.4 Setting Functions 35
- 1 [HOLD] Hold Function 36
- 2 [ZERO] Auto-zero Function 37
- Chapter 6 Normal Mode 38
- OUT1 • • • OUT4 41
- AREA1CALIB • • • AREA4 42
- PROGRAM 44
- HEAD1 HEAD2 HEAD3 HEAD4 45
- LASER ON AREA SETUP 47
- OUTPUT MODEOUT1LASER ON P. 1 49
- SELF-TIMING 49
- INTERVAL (ms) 49
- OUTPUT OUT1 • • • OUT4 50
- Measures 52
- A Digit Suppression Function 60
- B Offset Function 61
- C Analog Output Function 63
- LASER ON OUTPUT MODE 64
- D I/O Slot Setup 65
- E Inspection 66
- Optical axis 68
- H Display Unit 71
- I Area Check Function 72
- The current settings 73
- OK CANCEL 73
- Mode changed to Pitch 74
- Chapter 7 75
- 7.1 Pitch Mode Screens 76
- 7.2 Initial Screen 77
- 7.3 Setting Measurement 78
- 7.4 Setting Functions 79
- Chapter 7 Pitch Mode 80
- The number 83
- Missing pin 84
- HEAD1 Err 84
- Max - - - - - - 84
- Min - - - - - - 84
- HEAD1 • • • HEAD4 85
- Mode Description 87
- MODE CHANGE 91
- Chapter 8 93
- Chapter 8 RS-232C I/O 94
- 8.2 Remote Control Function 96
- Control Command 1 99
- Function Command received 100
- Description 100
- Selection 50H##0DH 100
- Reading Preset Data (Batch) 101
- Writing Preset Data (Batch) 102
- 8.3 Command List 103
- Sample Program (BASIC) 104
- Chapter 9 105
- 12 11 10 987654321 106
- 9.1.2 I/O Terminal Operations 107
- 9.1.3 Specifications 108
- Chapter 10 109
- 10.1 Display System Setup 110
- OPTION SETUP 111
- 10.1.3 Adjusting Contrast 112
- SELF-CHECK 112
- LS SYSTEM SETUP 112
- TO RUN MODE 112
- 10.1.6 Numeric Keys 115
- SYSTEM MODE 116
- Align the corners of 117
- ■ LS-5501 118
- ■ LS-5001 118
- Appendices 119
- Appendix B Initial Settings 122
- PITCH Mode 123
- ProblemItem 124
- Inspection 124
- Ref. page 124
- WARRANTIES AND DISCLAIMERS 131
Manuais e produtos relacionados com Sensores Keyence LS-5000
Sensores Keyence GP-M Series Manual do Utilizador
(28 páginas)
(28 páginas)
Sensores Keyence AP-C30KP Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-C30WP Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-V42A(P) Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-40P Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence SK-1000 Series Manual do Utilizador
(24 páginas)
(24 páginas)
Sensores Keyence DL-CL1 Manual do Utilizador
(78 páginas)
(78 páginas)
Sensores Keyence SK-H Series Manual do Utilizador
(12 páginas)
(12 páginas)
Sensores Keyence IV Series Manual do Utilizador
(10 páginas)
(10 páginas)
Sensores Keyence IV Series Manual do Utilizador
(6 páginas)
(6 páginas)
Sensores Keyence IV Series Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence IV Series Manual do Utilizador
(110 páginas)
(110 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais