Keyence DL-RS1A Manual do Utilizador descarregar pdf (Página 18)

Communication Response Time

 T5 (Response send time from DL-RS1A)

The time required to send a response varies depending on the communication speed, data bit

length, and number of bytes.

For information on the communication settings, refer to page 2.

The response time can be calculated using the following formula:

T5 = (number of bytes) x (data bit length + 4) / (communication speed)

z Number of bytes for different commands

SR command : (number of bytes in the read data) + 12

M0 command : {(number of bytes in the read data) + 1} × number of connected sensor amplifiers + 4

MS command : {(number of bytes in the read data) + 3} × number of connected sensor amplifiers + 4

DRQ input : {(number of bytes in the read data) + 3} × number of connected sensor amplifiers + 4

SW command : 11

AW command : 8

* For information on the number of bytes in the write data and the number of bytes in the read data,

refer to "Parameters of Commands and Responses" (page 10).

Sample calculation

 T6 (Sensor amplifier settings change time)

SR command : T6 = 0 ms

AW command

Up to 5 amplifier units: T6 = 0 ms

6 amplifier units or more: T6 = 25 ms

From the completion of the T4 command processing until after the T6 period, the sensor amplifier will

complete modifying settings. When T6 = 0 ms, the applied data of modified settings after receiving a

response (after T5 period), can be read using the read commands (M0, MS) or DRQ input.

In the event that the below data numbers are written using the SW, AW commands, the sensor

amplifier will reset. The measurement values after settings are applied can be read after (T6 +

T) period processing. By using the read commands (M0, MS) or DRQ input prior to T period

processing, the P.V. values that are read will be (-99.998) (------).

Number of bytes Data length Communication speed Response time

21 8 bit 9600 bps 26 ms

114 8 bit 9600 bps 143 ms

21 7 bit 38400 bps 6 ms

114 7 bit 38400 bps 33 ms

Point

Data numbers T

6: Set system parameter request Response time

133: Averaging Response time

Specifications

Performance Specifications

The following table shows the performance specifications for DL-RS1A.

Communication Specifications

The following table shows the communication specifications for DL-RS1A.

Item Specifications

Model DL-RS1A

Power supply voltage

20 to 30 VDC, including 10% ripple (P-P). Class2

(Supplied from the connected IL Series)

Current consumption 25 mA max.

Indicators

2 communication status indicators (green), alarm indicator (red), power indicator

(green)

Environ-

mental

Ambient

temperature

-10 to +55°C (No freezing)

Relative

humidity

35 to 85% RH (No condensation)

Vibration 10 to 55 Hz, compound amplitude 1.5 mm, 2 hours for each of XYZ axes

Material Main unit housing: polycarbonate

Weight Approx. 53 g

Accessories

Instruction manual, 2 end units, expansion connector cover, switch protection

sticker

Item Specifications

Communication method Full duplex

Synchronization method Asynchronous

Transmission code

ASCII

Communication speed

(Baud rate)

2400, 4800, 9600, 19200, 38400 bit/s

(Factory default: 9600 bit/s)

Data bit length 7 or 8 bits (Factory default: 8 bits)

Parity check None, even, odd (Factory default: none)

Stop bit length 1 bit

Data delimiter

Receive: automatically detect CR or CR + LF

Send: fixed to CR + LF

1 2 ... 13 14 15 16 17 18 19 20 21 22

Comentários a estes Manuais

Sem comentários

Keyence DL-RS1A Manual do Utilizador Página 18

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Keyence DL-RS1A