Keyence KV Series Manual do Utilizador

Super-small Programmable LogicController with Built-in DisplayKV SeriesExpansion Unit Instruction Manual96M11802*96M11802-1*

8KV-E4R/E4T/E8R/E8T(P)/E16R/E16T(P)(EXPANSION OUTPUT UNIT)Part names and functions012READY/ERROR3C1V1 V3 V5V4V2023OUTOUT1KV-E4REYENCEch.oNemaNnoitcnuF

9ledoMR4E-VKR8E-VKR61E-VKepyttinUtuptuoyalertniop-4tuptuoyalertniop-8tuptuoyalertniop-61stuptuoforebmuN 48 61epyttuptuO yaleRdohtemnoitcennoclanretxE

10KV-E8R (8-point expansion output unit (relay output type)) Terminal layout drawing Output circuit diagramC2 5 7 V446V3C1 1 3 V202V17654C2V4V3V1V2

11Output specificationsKV-E4T/E8T(P)/E16T(P) (Transistor output type(NPN/PNP))ledoMT4E-VK)P(T8E-VK)P(T61E-VKepyttinUtuptuorotsisnarttniop-4tuptuorotsi

12KV-E8T(P) (8-point expansion output unit (transistor output type)) Terminal layout drawing Output circuit diagramC2 5 7 V446V3C1 1 3 V202V17654C2

13KV-E4XR/E4XT(P) (EXPANSION I/O UNIT)Part names and functions012 3012 3C1C2 Y1 Y3 V4Y2 V3Y0X0 X2 V1X3 V2INOUTX1KV-E4XREYENCEREADY/ERRORch.oNemaNnoit

14Output specificationsKV-E4XR (Relay output type)metIsnoitacificepSepyttuptuO yaleRdohtemnoitcennoclanretxE etalplanimreTegatlovdaoldetaR )daolevitsi

15KV-E4XT(P) (Transistor output type)metIsnoitacificepSepyttuptuO )PNP(/)NPN(rotsisnarTdohtemnoitcennoclanretxE etalplanimreTegatlovdaoldetaR CDV03tne

16INSTALLATION ENVIRONMENT• Locations exposed to direct sunlight• Locations whose ambient temperature is outside the allowable range of 0to +50°C (32

17INSTALLATION PROCEDUREThis section describes how to attach a connected unit directly to a panel, toa DIN rail, or to a DIN rail with an expansion un

CONTENTSSafety Precautions ... 1Precautions on Regulations and Sta

18 Attaching the spacer to the expansion unitInsert the upper claw of the spacer into the upper groove of the expansionunit and press the lower claw

19 When I/O signal lines cannot be separated from the wiring for powerIn such a case, perform grounding on the KV side using batch-shieldedcables. (I

20Note 1: Use a load coil whose rating is less than the contact capacity.Note 2: Use a diode whose peak inverse voltage is 10 times or more the circui

21Be sure to turn off the power before connecting or disconnectingexpansion cables. If they are connected or disconnected while thepower is on, the un

22 KV-E4R/E4T/E8R/E8T(P)/E16R/E16T(P) (Expansion output unit) KV-E4XR/E4XT(P) (Expansion I/O unit) Expansion unit spacer*DIMENSIONS KV-E4X/E8X/E16

231119925384-ø5.0(mounting hole)Main unitmounting hole*(2 positions)* Two M3.5 countersunk-head screws are included for mounting the main unit.t=2OP

KEYENCE, at its sole option, will refund, repair or replace at no charge any defective Products within 1 year from the date of shipment. Unless stated

1WARNINGCAUTIONNote:SAFETY PRECAUTIONSThis instruction manual describes the operation and function of the KV.Read this manual carefully to ensure safe

2PRECAUTIONS ON REGULATIONS AND STANDARDS CE MarkingKeyence Corporation has confirmed that this product complies with theessential requirements of th

3INSPECTION AND MAINTENANCEInspectionWhile basic units and other units have been used for a long period of time,the connector connection area may beco

4SPECIFICATIONSmetIsnoitacificepSepytylppusrewoPcisaBstinuepytrewopCAepytrewopCD)P(TA/RA01-VK)P(TA/RA61-VK)P(TD/RD01-VK)P(TD/RD61-VK)P(TA/RA42-VK)P(TA

5KV-E4X/E8X/E16X (EXPANSION INPUT UNIT)Part names and functions➮For more about the general specifications, refer to "Specifications" on pag

6Terminal layout drawings and input circuit diagramsKV-E4X (4-point expansion input unit) Terminal layout drawing Input circuit diagramV1 V3 V5C1 1

7KV-E16X (16-point expansion input unit) Terminal layout drawing Input circuit diagramC3 9 11 C4 13 15810 1214C1 1 3 C2 5 702 462C1130 6C257410C3 9