Keyence LS-3100/3100W Series Manual do Utilizador Página 53
- Página / 104
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
47
CHAPTER 4 Functions and Controls
Tab le of I/O
Terminals
Analog Voltage Output
Analog voltage signal for CH1 can be obtained through the MON terminals.
The LS controller has been factory-set to convert a range from -60 mm to
+60 mm into a voltage range from -6 V to +6V. (No voltage signal is provided
for CH2. If voltage signal for CH2 is required, consult the KEYENCE distribu-
tor.)
Analog voltage range: A range between -6 V and +6 V can be set to
match a desired measurement range. Any value between -999.9999 and
9999.9999 can be selected. Note, however, that the difference between the
maximum and minimum measurements (those that you specify to corre-
spond respectively to +6 V and -6 V) must fall within a range between 0.024
mm and 240 mm.
Calibration: When the segment selectors are calibrated, the analog voltage
signal through these terminals and RS-232C interface is automatically sent
based on the calibrated value.
Offset: When the segment selectors are calibrated, the selected offset
value is added to the analog voltage signal sent through these terminals and
RS-232C interface.
The analog voltage which appears on the main display and that which is
output through the MON terminals are always the same.
Comparator Output
For CH1 (Channel 1)
HI3
HI2
HI1
GO
LO1
LO2
LO3
HIGH
GO
LOW
HIGH
GO
LOW
HI1
GO
LO1
HIGH
GO
LOW
HIGH
GO
LOW
HI
GO
LO
CH1
CH1
CH2
For CH2 (Channel 2)
CH2
7-step differentiation
3-step differentiation
Only 3-step
differentiation is
available.
Tolerance Limit Output Device/Terminal
Control I/O (open-collectors)
Comparator output terminals (relays)
Front panel (LEDs)
Control I/O (open-collectors)
Comparator output terminals (relays)
Front panel (LEDs)
CH1
Control I/O (open-collectors)
ls3100_30_48.p65 08.10.1, 10:55 AM47
- LS-3100(W) Series 1
- Unpacking 3
- WARRANTIES AND DISCLAIMERS 3
- CONTENTS 4
- Chapter 8 Error Messages 78 6
- Appendices 83 6
- WARRANTIES AND DISCLAIMERS 97 6
- LASER SAFETY PRECAUTIONS 7
- 1-4 Safety Consideration 8
- 1-3. Label Location 8
- LS-3060LS-3060 9
- LS-3032, LS-3034, LS-3036 10
- LS-3033, LS-3033 SO, LS-3060 10
- Grounding the 11
- Serial No 12
- Connect the correct scanning 12
- CHAPTER 2 13
- TRIAL OPERATION 13
- CHAPTER 3 14
- QUICK SETUP PROCEDURES 14
- 3-1. Common Settings 15
- 3-2. Measurement Procedures 16
- Gap Measurement 1 17
- Gap Measurement 2 17
- MODE NOMAL 18
- MODE P–P 18
- SEG D I A 18
- S E G E DGE1 18
- Measuring Target 19
- Displacement within 19
- Measuring Edge 19
- Movement 19
- Measuring Outer Diam 20
- Front Panel 21
- LS-3100 Series 21
- Back Panel 22
- LS-3033T 23
- LS-3033R 23
- 4-2. Indicators and Displays 24
- 4-3. Panel Keys 25
- See P.39 26
- See P.20 26
- See P.43 26
- Averaging Methods 27
- Analog Voltage Range 28
- See P.32 29
- See P.63, 64 30
- See P.63 30
- See P.29 31
- DIGIT SUPPRESS 32
- BAUD RATE 33
- POSITION CHECK 34
- Definition of Segment 36
- Description 36
- SEG ( 3 , 3 ) 37
- Segment Selector 38
- See P.31 39
- See P.31 40
- Segment Check 41
- Output Channel 43
- See P.43 or OFFSET value 44
- Transmitter 44
- Receiver 44
- MODE, OFFSET, and LIMIT 45
- C MODE Key 46
- 35 2. 345 50
- 2 36 1. 234 50
- G PROG (Program) 51
- See P.62 52
- Analog Voltage Output 53
- Comparator Output 53
- Specifications 55
- Pin Assignment 55
- Remote Operation 56
- Measurement in "mm" 60
- SP SP 6 0 . 0 0 0 0 63
- -SP60 . 0000C 63
- SP SP 1 0 . 0 0 0 0 CR 65
- -SP10 . 0000CR 65
- 1st data 2nd data 66
- Pin assignment 68
- Input Signal 69
- Output Signal 69
- Control Input Terminals 70
- Control Output Terminals 70
- MOUNTING SCANNING HEAD 71
- OS TP IOI N CHECK 72
- LED 7 lights 73
- CHAPTER 6 74
- OPTIONAL INTERFACE BOARDS 74
- 6-1. BCD Output 74
- External Trigger Input 76
- (EXT TRIG IN) 76
- Setting Address 78
- Setting Talk Only Mode 78
- Setting Delimiter 78
- Values or Other Data 79
- Talk Only Mode 79
- Setting Functions and 79
- Outputting Measured 79
- Status Byte 80
- Example of Program 81
- GP-IB Interface I/O 82
- Measuring Conditions 82
- CHAPTER 8 84
- ERROR MESSAGES 84
- CHAPTER 8 Error Messages 85
- CHAPTER 9 86
- TROUBLESHOOTING GUIDE 86
- OPERATING PRINCIPLE 89
- CHARACTERISTICS 90
- Temperature 91
- Characteristics 91
- (Typical) 91
- SPECIFICATIONS 92
- Scanning Head 93
- Approx.34 94
- APPENDIX E 95
- QUICK REFERENCE TABLE 95
- KEY FLOWCHARTS 97
- APPENDIX F Key Flowcharts 98
- FNC (Function) 100
- APPENDIX F Key Flowcharts 101
- APPENDIX F Key Flowcharts 102
- SAFETY PRECAUTIONS 103
Manuais e produtos relacionados com Sensores Keyence LS-3100/3100W Series
Sensores Keyence GP-M Series Manual do Utilizador
(28 páginas)
(28 páginas)
Sensores Keyence AP-C30KP Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-C30WP Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-V42A(P) Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence AP-40P Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence SK-1000 Series Manual do Utilizador
(24 páginas)
(24 páginas)
Sensores Keyence DL-CL1 Manual do Utilizador
(78 páginas)
(78 páginas)
Sensores Keyence SK-H Series Manual do Utilizador
(12 páginas)
(12 páginas)
Sensores Keyence IV Series Manual do Utilizador
(10 páginas)
(10 páginas)
Sensores Keyence IV Series Manual do Utilizador
(6 páginas)
(6 páginas)
Sensores Keyence IV Series Manual do Utilizador
(5 páginas)
(5 páginas)
Sensores Keyence IV Series Manual do Utilizador
(110 páginas)
(110 páginas)
Sensores Keyence IV-D10 Manual do Utilizador
(2 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais