Keyence LT-9001 Series Manual do Utilizador descarregar pdf (Página 170)

Index

[PAUSE] button ................................................1-6

Pause screen............................3-2, 3-9, 4-2, 4-10

Peak hold [PEAK] ............................5-9, 5-11, 7-9

Peak-to-peak hold [P-P]............................5-9, 7-9

PLC...................................................................

8-1

Point data update cycle .................................7-11

Power LED........................................................1-4

Power ON reset time ........................................9-6

PROF OUT (Profile output) .............................4-19

Power switch ....................................................1-5

Profile graph display ........................................4-3

Profile mode ....................2-2, 2-9, 2-24, 4-1, 5-18

Profile output cycle.........................................7-11

Profile output time .................................7-11, 7-15

Profile waveform....................................7-11, 7-12

Profile waveform data output ....................

8-4, 8-6

Profile waveform graph display........................4-4

Profile waveform output range .......................7-11

Program .............................................2-8, 6-2, 6-6

Program change ..............................................5-6

Program change screen ...........................3-2, 4-2

Program function..............................................2-8

Program mode .................................................2-5

Program mode screen ..............................3-2, 4-2

Program No. change.................................7-4, 7-6

Program setting selection method [P-SELECT]

...6-2

[PROG/RUN] switch..................................1-6, 6-4

[PROGRAM No.] button ...................................1-6

Program copy [P-COPY]...........................6-2, 6-6

Range of light intensity graph ..........................4-4

Range of profile graph .....................................4-4

Received light intensity graph ..................3-7, 4-8

Remote control console ............................1-6, 6-6

Remote control console connector ..................1-4

RESET .......................................................

8-4, 8-6

Reset input ................................................7-3, 7-5

RESET time ....................................7-9, 7-13, 7-14

Resetting the devices to the factory settings

.....2-22

Response command ........................................

8-3

Response delay time........................................9-6

RS-232C ...........................................................

8-1

RS-232C cable.................................................A-5

RS-232C connector..........................................1-4

RS-232C conversion adapter ..........................A-5

Run Mode.........................................................2-4

Sample hold [SAMPLE]....................5-9, 5-13, 7-9

Sampling cycle ..............................7-9, 7-13, 7-14

SCAN ....................................................3-15, 4-14

Scan center...........................................3-16, 4-15

Scanning change time ............................7-9, 7-15

Scanning settings display bar..........................3-3

Scanning width cursor .....................................4-3

Scan width/interval................................3-15, 4-14

Screen change.................................................

8-4

[SCREEN] button..............................................1-6

SCROLL .........................................................5-18

Scrolling mode

.....................................................5-18

Selecting an Item ...........................................2-11

Selecting the displacement mode .................2-13

Selecting the measurement target surface ....3-13

Selecting the profile mode .............................2-16

Selection method of the run mode .................2-12

SELECT SURFACE (Select surface)

................................................3-8, 3-12,

8-8, 8-10

Select surface

position display bar

............3-3, 4-3

Select surface display......................................3-4

Setting of number of data to be averaged .....

8-10

Setting the area ..............................................2-18

Setting the light Intensity level ................2-15, 4-8

Setting the position ...................................3-7, 4-7

Setting the scan width/interval ..............2-14, 2-17

Setting the upper and lower limits of

the graph display ......................................3-6, 4-6

Setting the upper and lower limits display .....2-18

Single display............................................3-5, 4-5

Slant ...............................................................3-10

Slant correction .....................................3-10, 4-11

SMOOTH (average in profile mode only).......4-17

Smoothing .............................................4-17,

8-13

SPAN.........................................................6-3, 6-7

Span adjustment ..............................................6-2

Specifications of the cable between the

Measuring unit and the controller ....................9-5

Specifications of the controller.........................9-2

Specifications of the measuring unit ................9-3

SRAM sum error...............................................A-4

STABILITY ........................................................7-5

Stability output ..........................................7-4, 7-5

A-14

E LT-9001-IM

Note: Pages marked in BOLD print refer to RS232C parameters, settings, etc.

Appendices

LT-9000-M-APP-E.qxd 10.4.8 6:02 PM ページA-14

1 2 ... 165 166 167 168 169 170 171 172 173 174 175 176

Comentários a estes Manuais

Sem comentários

Keyence LT-9001 Series Manual do Utilizador Página 170

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Keyence LT-9001 Series