Keyence Visual KV Series Manual do Utilizador Página 275
- Página / 392
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
4.7 Examples of Direct Clock Pulse Output
3-251
Visual KV
Series
1
4
Chapter 4 High-speed Counters
4.7.4 Application of Direct Clock Pulse Output
(Ramp-up/down control)
The following ramp-up/down control is available by setting four parameters (DM0000
to DM0003)
■ Setting parameters
DM0000: fH [Hz] (Running frequency)
DM0001: fL [Hz] (Start-up frequency)
DM0002: Acceleration rate [Hz/10 ms]
DM0003: No. of pulses for positioning
Note 1: A smaller acceleration rate allows smoother control but extends the accel-
eration time.
Note 2: Be sure to turn OFF input 0007 (phase B input).
■ Operation
In the example on the next page, each parameter is set as follows:
DM0000: 8000 [Hz]
DM0001: 700 [Hz]
DM0002: 400 [Hz/10 ms]
DM0003: 4000 pulses
When start switch 0000 is pressed, ramp-up/down control is performed as shown
below. Control is stopped when the pulse count reaches "4000".
Pressing the start switch restarts the operation. The operation is reversed while
reverse switch 0001 is ON.
■ Connection example
The above diagram shows a connection example between the KV PLC and a
stepping motor driver.
Refer to the instruction manual for your stepping motor driver for details.
Set the pulse input method of the stepping motor driver to "1-pulse input method".
CW
KV
24 VDC
FG
–
+
–
+
–
+
5 VDC
+–
CCW
0002
0001
0000
0502
0500
COM
0003
0501
COM
0503
Stepping motor
Start
Reverse
output
Emergency
stop
Stepping motor driver
Twisted-pair cable
(Pulse)
(Rotation
direction)
Specify values in the range from 153 Hz to
50000 Hz. The fH value must be greater
than the fL value.
➞ (fH - fL) / (Acceleration time / 10 ms)
➞ Must be 65534 pulses or less.
L
(DM0001)
H
(DM0000)
10ms
(DM0003)
(DM0002)
0
Frequency (Hz)
Acceleration
rate
(Acceleration
change period)
Total pulses
for positioning
Acceleration
time
Constant
speed time
Time (ms)
Deceleration
time
➞
KVNKA Chap 04_2.p65 08.3.11, 0:08 PM251
- Programming 1
- Safety Precautions 2
- WARRANTIES AND DISCLAIMERS: 2
- Note to User 3
- How this manual is organized 8
- Contents 10
- Chapter 2 Instructions 11
- Installation 13
- Chapter 6 Handheld Programmer 17
- 2 Support software 20
- Chapter 2 Editor KV-300 21
- Chapter 3 Simulator 22
- Chapter 4 Monitor 22
- Appendices 23
- WARRANTIES AND DISCLAIMERS 24
- Chapter 1 25
- 1.1 Before Creating Programs 26
- 1.1.2 Scan Time 27
- 1.2 User Memory 28
- 1.3 Device Configuration 29
- Chapter 1 Programming 30
- 1.3.2 Relay No 31
- 1.3.3 Assigning Relay Nos 32
- 1.3.4 Input Relays 33
- 1.3.5 Output Relays 34
- 1.3.6 Internal Utility Relays 35
- 1000 turns ON at every hour 36
- Other special utility relays 39
- 1.3.9 Timers and Counters 42
- 1.3.10 Data Memories 43
- 1.3.11 Temporary Data Memory 45
- 1.4 Special Functions 47
- Modification within the CPU 48
- 1.4.3 Constant Scan Time Mode 49
- 0000 2300 50
- 1.5 Extended Ladder Diagrams 51
- 0000 2301 52
- Chapter 2 57
- 2.1 Instruction List 58
- 2.1.3 Arithmetic Instructions 62
- 2.1.4 Interrupt Instructions 65
- 2.2 Instruction List 66
- 2.2.3 Arithmetic Instructions 72
- < DI > 78
- < EI > 78
- 2.3 Convention Details 79
- LD: Load 81
- LDB: Load Bar 81
- 0000 0001 82
- Incorrect 84
- ANL: And Load 85
- ORL: Or Load 87
- OUT: Out 89
- OUB: Out Bar 89
- SET: Set 90
- RES: Reset 90
- (TMR No.) 91
- TMH: 0.01-s Timer 92
- TMS: 1-ms Timer 93
- C: Counter 96
- 0002 C002 97
- Special utility relay 98
- (1-second clock) 98
- (Preset value) 100
- Low-order 101
- 4 digits 101
- High-order 101
- DIFU: Differentiate Up 102
- DIFD: Differentiate Down: 102
- Chapter 2 Instructions 103
- 2.4 Instruction Details 103
- KEEP: Keep 104
- SFT: Shift 106
- (Relay No.) 107
- Enable input 110
- 1) 2) 3) 111
- Turns ON 112
- 1-s timer 112
- MC: Master Control 113
- MCR: Master Control 113
- SW1SW2SW3SW4 116
- Details of MEMSW 117
- Description 117
- NOP: No Operation 118
- END: End 118
- ENDH: End Hi 118
- W-ON: Wait ON 120
- W-OFF: Wait OFF 120
- Operands 121
- Key operation 121
- W-UE: Wait Up Edge 122
- W-DE: Wait Down Edge 122
- 0503050205010500 126
- MPS: Push 127
- MRD: Read 127
- MPP: Pop 127
- Start of branch 128
- Connection of branch 128
- End of branch 128
- MPS MPS MPS MPS 129
- STG: Stage 130
- JMP: Jump 130
- ENDS: End Stage 130
- Details of STG instruction 132
- Initial setting 134
- Reset input 134
- STG start relay 134
- STG end relay 134
- Double coil 135
- Interlock 135
- 3 seconds 136
- STP: Step 138
- STE: Step End 138
- ITVL: Interval Timer 141
- Setting procedure 142
- CALL: Subroutine Call 146
- SBN: Subroutine Entry 146
- RET: Subroutine Return 146
- Subroutine program 148
- FOR: Repeat Start 149
- NEXT: Repeat End 149
- Indirect addressing 151
- This operation is repeated 153
- DM0000 is 153
- HKEY: 16-Key Input 155
- BCD Digital switch 157
- 2.4.3 Arithmetic Instructions 158
- Internal register 159
- @xxxx: Differentiation 161
- TMIN: Trimmer In 162
- Trimmer Setting 162
- LDA: Load A 164
- @LDA: Load A 164
- STA: Store A 164
- @STA: Store A 164
- Arithmetic flag 165
- CMP: Compare 170
- @CMP: Compare 170
- Hexadecimal 174
- ResultArithmetic operation 174
- ADD (Addition) 175
- DM0003) into DM100 176
- (Stores positive value) 177
- (Stores negative value) 177
- Positive value DM0002 177
- Negative value DM0003 177
- Hexadecimal number 179
- Remainder 180
- Quotient 181
- (DM0001+DM0002+DM0003) 182
- (DM0000) ^ ($00FF) = (DM0001) 183
- (Logical sum) 185
- Exclusive Or A 188
- (Exclusive 188
- @SLA: Shift Left A 190
- SRA: Shift Right A 190
- @SRA: Shift Right A 190
- SLA: Shift Left A 190
- RRA: Rotate Right A 193
- @RRA: Rotate Right A 193
- RLA: Rotate Left A 193
- @RLA: Rotate Left A 193
- Complement 195
- (Bit inversion) 195
- 0000 DM0000 197
- 7-segment display 203
- TBCD: Transfer BCD 204
- @TBCD: Transfer BCD 204
- TBIN: Transfer BIN 204
- @TBIN: Transfer BIN 204
- DM0000 x DM0001 = 206
- ... TM01 206
- ÷ #10000 206
- ROOT: Square Root 209
- @ROOT: Square Root 209
- 2.5 Programming Notes 213
- Programming precautions 214
- Chapter 3 215
- Interrupt 216
- Visual KV 217
- 3.2 Interrupt Processing 218
- 3.2.2 Types of Interrupts 219
- 3.2.3 Interrupt Priority 220
- 3.2.4 Interrupt Program 220
- 3.3 Direct Input/Output 221
- Two Points 225
- Chapter 4 227
- Input-enable relay 228
- Count input 228
- 1. KV-300/Visual KV only 228
- 2. Visual KV only 228
- * Read-only relay 231
- Counters 235
- 4.3.4 Count Input Method 236
- (Counter value) 237
- External 239
- (single-phase input) 248
- 4.4.4 Ring Counter Function 249
- 4.5.5 Cam Switch Function 257
- 4.6 Direct Clock Pulse Output 261
- Comparator 262
- Pulse period 263
- ON ON ON ON 264
- 00220.1 µs005 268
- 10220. 01 µs05 268
- 20220. 001 µs5 268
- Pulse Count 273
- (Ramp-up/down control) 275
- Chapter 5 277
- Upper digit 278
- Lower digit 278
- Procedures 279
- 5.2.2 Operating Procedure 281
- Control Function 282
- Function 283
- Set parameters for auto 290
- Stop pulse output at the 290
- Chapter 6 291
- 6.1 Interrupt Instructions 292
- Interrupt priority 293
- Interrupt routine 293
- Direct output 294
- Direct input 294
- 6.1.2 Interrupt Instructions 295
- INT: Interrupt 296
- RETI: Return Interrupt 296
- Pulse width 297
- 2206(OFF) 2206(ON) 297
- Example 3 298
- 6.1 Interrupt Instructions 299
- 6.2 Direct Clock Pulse 300
- For KV-10/80 users 301
- 6.2 High-speed Counters 302
- Outline of Pulse Output 303
- KV-10/80 307
- 2100 2200 1.0 µs 10 to 65535 307
- 2101 2201 10.0 µs1 to 65535 307
- 2102 2202 100.0 µs1 to 65535 307
- CTH0 value 308
- CTH1 value 310
- * Refer to page 3-276 311
- *Refer to page 3-276 314
- 0000001001101000 316
- Special utility 316
- 6.3 Positioning Control 320
- Setting parameters 321
- Preset frequency 322
- Run frequency 323
- Start frequency 323
- 6.3 Positioning Control 324
- Ramp-up/down control 325
- Chapter 7 329
- 10 ms or longer 332
- 100 ms or longer 332
- 7.2 Serial Communication 333
- Commands 335
- 7.2.5 Other Response Codes 339
- 7.2.6 Error Code List 340
- 7.2.7 Example Program 341
- 7.3 Loading Text Data 342
- 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 343
- 7.3.3 Sample Program 344
- 7.4 ASCII Code List 345
- 7.4 ASCII Code List 346
- Chapter 8 347
- 8.1 List 348
- Basic Instructions 350
- 8.2 Details 351
- Application Instructions 358
- Transfer 365
- Refer to p. 3-131 366
- Arithmetic Instructions 367
- Sets C001 381
Manuais e produtos relacionados com Sensores Keyence Visual KV Series
Sensores Keyence MS-F07 Manual do Utilizador
(2 páginas)
(2 páginas)
Sensores Keyence MS2 Series Manual do Utilizador
(2 páginas)
(2 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.152 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais